Precision casting & CNC machining since 2000
Precision Casting, Trusted Worldwide

News

EV Battery Tray Die Casting: Design, Safety & Thermal Management

EV battery tray structural casting: part consolidation and Sureton 88 to 800 tonne scope
Mega-casting consolidates the rear underbody. Sureton’s 88 to 800 tonne presses serve the tray sub-components around it.

In electric vehicles, driving range still comes down to mass. The battery cells are dense by design, but the enclosure that protects them, the battery tray or battery enclosure, is one of the largest single components in the car. Trimming weight there is the fastest way to add range without touching the pack.

For years these enclosures were built from stamped steel or extruded aluminium, joined by hundreds of welds and fasteners. The industry is now moving the other way: casting the structure as one complex aluminium part. That shift changes how engineers think about alloys, process control, and where the cooling actually happens.

1. The structural mandate: crashworthiness

A battery tray is not a box. It is a safety-critical member that has to manage crash energy and keep the cell pack intact. The difficulty is that the alloys which flow best in high-pressure die casting, A380 and ADC12, are also the least ductile. In a crash they can crack instead of absorbing energy.

The answer is a different alloy family: Al-Si-Mg(-Mn) structural grades with tightly controlled iron. The European EN grade AlSi10MnMg is the one most often cited for cast structural parts. In the as-cast (heat-treatment-free) condition it typically lands at yield strength 120 to 160 MPa, ultimate tensile strength 280 to 310 MPa, and elongation of 8 to 12 percent. Those numbers come from supplier and OEM material data sheets, not from any single foundry, and they are why a non-heat-treated structural casting can bend rather than shatter.

2. Thermal management: the tray is the heatsink

Battery packs shed heat, and the tray is part of that path. Two routes dominate. One is to machine cooling channels into a plate after casting. The other is to build the channel geometry into the die so the tray comes out as a near-complete cooling structure.

Casting the channel in place removes a machining step and a leak path, but it demands clean filling and tight control of wall thickness. As liquid cooling spreads through EV platforms, this is becoming a standard expectation rather than a premium option. (One market report puts liquid cooling at roughly half of new AI data-center deployments in 2026, and the same thermal logic is pushing automotive enclosure design.)

3. The scale challenge: megacasting

When the part grows past 1.5 meters, the economics flip toward very large presses. The clearest example in production is the Volvo EX60 rear underbody, in series output at the Torslanda plant in Sweden since April 2026. Two Bühler Carat 840 cells, each rated at 8,400 tonnes of locking force, inject more than 200 kg of aluminium per shot and replace roughly 100 stamped and welded parts with one casting. Bühler states that eight of the world’s ten largest vehicle makers now use megacasting.

Sureton does not run giga-casting or megacasting presses. Our die casting line runs from 88 to 800 tonnes. That is the honest scope: we are not the press that makes the one-piece underbody. We are a supplier for the parts that bolt to it.

4. Where high-vacuum HPDC earns its place

Battery-tray sub-components, brackets, busbar covers, mounting frames, still need low porosity and consistent strength. That is where high-vacuum HPDC matters. Pulling the cavity to a deeper vacuum before fill cuts gas porosity, which in turn improves leak tightness and mechanical repeatability on thin structural sections.

The industry reference point is a vacuum level around 50 mbar or better and porosity below 0.5 percent at the Tier-1 threshold, with process capability tracked at Cpk 1.67 on critical features. Those are supplier-capability targets, not Sureton’s own published values, but they describe the bar a tray program is measured against.

5. What Sureton makes for battery trays

Within the 88 to 800 tonne range we cast the structural and mounting pieces that surround the cell pack: aluminium brackets, housings, busbar covers, and frame details. Where the design needs it, we offer high-vacuum HPDC, cast-in cooling features, and CNC finishing to hold features at about plus or minus 0.05 mm as-cast and plus or minus 0.01 mm after machining.

If you are scoping a tray program, the useful questions are practical: what vacuum grade, what porosity target, and whether the cooling channel is cast in or machined. Send the drawing and we will tell you which of those we can hold and where the trade-offs sit.

Related reading: our take on EV lightweighting with structural aluminium, how vacuum die casting controls porosity, and reaching 1.0 mm thin walls. Start with how die casting works for the basics, and see what tooling actually costs before you commit to a program.

Authoritative references

Independent third-party standards and industry bodies, provided for further reading. Sureton is not responsible for third-party content.

Latest News

Small Molded Parts with in Days

Sureton complete Die Casting and CNC machining service will accompany your brand project from the prototype construction to the end metal precision parts manufacturing.

Scroll to Top
Sureton Company Logo – Precision Manufacturing & Industrial Solutions

Get in Touch

If you cannot find a suitable product, please leave a message or contact us. We have a dedicated technical team to serve you.

Sharing Your 2D Drawings & 3D Models Will Help Our Engineers to Quote Faster.

Note that, Max 100MB/file, Support: pdf, dwg, dxf, drw, iges, igs, ipt, jpg, jpeg, it, step, stp.stl, sat, sldasm, sldprt, siddrw, png.svg,x_t,xb,3dxml, 3mf, zip…If your file is not supported, please compress it into zip and upload