When you spec a metal enclosure or a piece of hardware, two decisions drive everything else: the alloy, and whether you cast the part or machine it. Both come down to the same few facts about the part. Settle them before you build the tool, because fixing them after first articles costs far more.

Question 1: What is your annual volume?
CNC needs no hard tooling, so it wins at low volume and on designs that are still moving. Die casting starts with a hardened steel tool that usually takes about 45 days to cut. That tool cost gets divided across every part it makes, so the per-part price drops as volume climbs. For most programs the crossover sits somewhere in the low thousands of units a year, though the exact point depends on part size and complexity.
Question 2: How thin or intricate is the geometry?
Zinc casts thinner walls and finer detail than aluminium, and it holds tighter tolerances straight from the die. Thin-wall aluminium usually sits in the 2 to 4 mm band; go thinner and you fight fill and warpage. Zinc can drop under 1 mm in spots. Parts with lots of thin ribs, bosses and snap features are almost always cheaper to cast than to cut.
Question 3: Does the part need to move heat?
Aluminium is the natural choice when the part also has to shed heat, which is why it shows up in motor housings and heat sinks. Zinc does not move heat as well, so for a bracket or enclosure that sees heat, aluminium is the safer call.
Question 4: Which faces must be tight?
As-cast features commonly hold about plus or minus 0.05 mm. Sealing faces and bolt circles get finished by CNC to about plus or minus 0.01 mm. Spend machining only where the part actually seals or bolts, and leave the rest as-cast. Mark the critical faces on the drawing, and the cost stays where it should.
Question 5: What corrosion environment will it live in?
For indoor duty, standard surface treatments qualified to at least 480 hours of continuous neutral salt spray with no white rust (ISO 2409 Grade 2) support a five-year-plus service life. For harsher or longer service, premium treatments reach 720 hours or more at Grade 1, supporting a ten-year-plus duty cycle. Pick the finish from where the product lives, not from a catalogue.
Aluminium vs zinc (typical values)
| Property | Aluminium (die cast) | Zinc (die cast) |
|---|---|---|
| Typical thin wall | 2 to 4 mm | under 1 mm possible |
| Thermal conductivity | High (heat sinks, housings) | Lower |
| As-cast tolerance | about plus or minus 0.05 mm | about plus or minus 0.05 mm, tighter feasible |
| Best for | light, stiff, heat-dissipating parts | small, thin, intricate parts |
| Relative tool cost | moderate | moderate |
Die casting vs CNC (typical values)
| Factor | Die casting | CNC machining |
|---|---|---|
| Upfront tool | required, about 45 days | none |
| Unit cost at volume | low | higher |
| Geometry | thin walls, integrated features | any, easy design changes |
| Best volume | low thousands per year up | prototyping, low volume |
| Repeatability | identical parts | identical parts |
Frequently asked questions
What is the minimum wall thickness for die casting?
Thin-wall aluminium die castings typically land in the 2 to 4 mm range. Zinc can go under 1 mm in places because it flows at lower temperature and pressure. The practical minimum depends on how the metal reaches the far end of the cavity before it freezes.
When should I choose CNC machining instead of die casting?
CNC wins at low volume, when the design is still changing, and for parts with features that are awkward to cast such as deep internal threads. Die casting wins once volume climbs into the low thousands per year and the geometry has thin walls or integrated features.
How long does die casting tooling take?
A die typically takes around 45 days to design and cut, before any iteration needed to settle fill and shrinkage. Plan that window into the launch schedule.
What salt spray life can a coated die casting reach?
Standard surface treatments are qualified to at least 480 hours of continuous neutral salt spray with no white rust (ISO 2409 Grade 2), supporting a five-year-plus indoor life. Premium treatments reach 720 hours or more at Grade 1 for a ten-year-plus duty cycle.
Sureton Precision Manufacturing runs aluminium and zinc die casting (88 to 800 tonne presses) and in-house CNC for appliance, electronics and instrument hardware. This guide reflects established practice and stated capabilities; it is not a quotation or a guarantee of any specific part. Contact: [email protected]
Planning a project? See our die casting services in China.


